Welcome text

tokomesinfotocopy.blogspot.com-Google pagerank and Worth

Sabtu, 30 April 2011

Code error Canon Fotocopy

Code error Canon Fotocopy


Canon Error Codes E000 - E199

E code Description      Category         Remarks         
E000  The fixing temperature does not go up after turning ON the power due to a fault in the thermistor or the heater, etc., (e.g. It does not reach 70°C degrees within 2 min.)        Related fixing unit                 
E001    The fixing temperature abnormally goes up due to a fault in the thermistor or SSR, etc.     
E002    The fixing temperature does not reach a specific temperature due to a fault in the thermistor or the heater, etc.
e.g) The fixing temperature does not go up to 190°C degrees within 5 min after reaching 70°C degrees.  
E003    The fixing temperature drops abnormally after wait time is up due to a fault in the thermistor, the heater, etc. (e.g. After wait time is up, the fixing temperature drops to 70°C degrees). 
E004    A short circuit in the fixing heater drive circuit (SSR, etc) is detected.        
E005    The fixing web is wound up completely.       
E006    The fixing drawer connector is not connected as the front door is closed.   
E007    The fixing film is off to the side.       
E008    A specific number of copies are made after the machine detects that fixing oil is out.         Since a user cannot re-supply fixing oil, the error code is indicated.        
E009    The rated voltages of the power supply and the fixing unit do not match.               
E010    Clock pulses fail to be generated or the PLL lock fails to be released due to a fault in the main motor, etc.            Related drum drive unit and main drive unit
E011    Excess current flows to the motor control circuit because the main motor is locked up, etc.           
E012    Clock pulses fail to be generated or the PLL lock is released due to a fault in the drum motor, etc.            In case the drum drive motor exists in addition to the main motor, this code refers to an error of a motor which drives mainly other units than the drum.       
E013    •The PLL lock is released because waste toner motor is locked up, etc.
•The micro switch employed to detect clogging of waste toner is activated.
•The waste toner case is detected full.                      
E014    •The PLL lock of the fixing/feeding motor is released.
•Excess current of the feeding motor is detected.     
E015    •Clock pulses of the pick-up/duplexing/developing motor fails to be generated or be detected.
•Excess current of the pick-up/duplexing/developing motor is detected.     
E016    Excess current of the reciprocating motor of the photosensitive drum cleaner unit is detected.      
E017    The PLL lock of the drive motor of the holding tray unit is released.          
E018    The PLL lock of the drive motor of the oil removing roller is released.        
E019    The waste toner case is detected full although it is not.        
E020    The developer fails to be replenished with starter developer properly.          Related developing unit          A hopper motor error is identified by the detail code of E020. However, it may be identified by E02x according to need.     
E021    The rotor fails to rotate and move properly due to a fault in the developing rotor/motor ass'y.                   
E022    Pressure fails to be applied to the developer after a specific time passes after the developer is selected.    
E023    The developer sleeve motor fails to rotate properly.  
E024    The developer cannot be detected. ( not mounted properly.)
E025    Excess current of the toner delivery motor or the cartridge motor is detected.        
E030    The total counters are not functioning.           Related counter          
E031    The optional counters are not functioning.    
E032    The counters for ASSIST are not functioning. (Disconnection of counter pulse for ASSIST.)       
E040    The lifter position signal fails to be generated due to a lifter clutch failure.  Related paper pick-up unit     
E041    The paper deck lifter fails to be detected within a specific time.      
E042    The roll paper cutting operation is not functioning properly because the cut motor does not work, etc.      
E043    An abnormal signal is detected due to a fault in the pick-up motor for the 3-cassette deck/3.5K paper deck.           
E050    A malfunction of the holding tray. A fault in the side registration is included.        Related duplex unit    The duplexing unit for the stack system   
E051    The home position of the side registration cannot be detected within a specific time.          The duplexing unit for the through-path system   
E054    The home position of the duplexing unit feed roller cannot be detected.                 
E055    The horizontal registration guide of the duplex unit exceeds its maximum travel distance. 
E060    The home position of the primary corona wire cleaner cannot be detected within a specific time.   Relateted charging         
E061    Specific potential is not be required or the limiter is activated as the potential is controlled.           
E062    The photosensitive drum temperature does not reach a specific value due to a fault in the photosensitive drum heater, etc.        
E063    The home position of the transfer corona wire cleaner cannot be detected.  An error code is not to be indicated.       
E064    The setting value for the output from the microcomputer considerably deviates from the control value of the actual output.             
E065    High voltage leakage from the primary corona assembly is detected.           
E066    Signals from the temperature/humidity sensor cannot be detected.  
E067    Two or more faults in the primary/ pre (post)-transfer/ transfer/ separation high voltage are detected (including power output stoppage, electric leakage from the primary corona assembly).     
E068    High voltage leakage from or an open circuit in the separation corona assembly is detected.          
E069    High voltage leakage from or an open circuit in the transfer corona assembly is detected.  
E070    The home position of the transfer drum cannot be detected within a specific time.  Related transfer         
E071    An image leading edge signal cannot be detected within a specific time.    
E072    A fault in the main motors such as the transfer drum motor, etc.     
E073    The transfer drawer connector or the transfer frame drawer connector is not connected as the front door is closed.
E074    The transfer belt unit does not reach the target position within a specific time.       
E075    The transfer belt is off to the side.     
E076    The transfer belt web is wound up completely.         
E077    The motor inside the transfer belt unit has a fault.    
E079    The home position (to apply pressure) of the transfer drum cleaner unit cannot be detected.          
E080    An error occurs in the communication with the multi color unit controller PCB.      Related developing unit for multi color unit     
E081    The vertical motor clock is faulty.     
E082    The horizontal motor clock is faulty. 
E083    The CD unit horizontal movement right sensor is faulty.      
E084    The CD unit horizontal movement left sensor is faulty.        
E085    The CD unit feeder release sensor is faulty.  
E086    The CD unit claw release is faulty.    
E089    A malfunction of the multi color unit.           
E090    The document feed motor is not functioning properly.          related document feeder (bulit-into machine)           
E091    A failure in the detection of the document feed sensor.       
E100    The BD signal cannot be detected within a specific time.     Related laser  
E101    The AF motor of the laser unit is faulty.       
E102    The light intensity of the laser does not reach a specific level.          
E110    The polygonal scanner motor does not reach a specific speed within a specific time.           Related laser scnner 
E111    The polygonal cooling fan does not rotate properly. 
E120    The temperature of the laser does not reach a specific value. Related laser temperature control      
E121    The stoppage of the laser cooling fan is detected.     
E140    The movable guide motor is turned ON, and a specific position cannot be detected within a specific time.            Related BJ     
E141    1. The capping motor is turned ON, and a specific position cannot be detected within a specific time.
2. A specific position of the cam sensor for the recovery system cannot be detected within a specific time.           
E142    The pressure position switching motor is turned ON, and a specific position cannot be detected within a specific time.  
E143    The intake switching motor is turned ON, and a specific position cannot be detected within a specific time.           
E144    A detection signal is not returned to the ink pump monitor after the ink pump is activated: DCC -> BHD -> pump drive signal       
E145    No signal is generated from the position sensor within a specific time after a drive signal of the cutter motor is generated.   
E146    1. The waste ink full sensor is turned ON.
2. The intake counter for waste ink exceeds a specific value.           
E150    Neither thermistor nor trimmer resistance is connected to the head. (The head is not connected.)   Related BJ head   
E151    The thermistor of the head is open-circuited.
E152    The thermistor of the head is short-circuited.
E153    The trimmer resistance of the head is open-circuited.           
E154    The trimmer resistance of the head is short-circuited.           
E155    The trimmer resistance of the head is out of specifications.  
E156    When a specific voltage is applied to the head, the voltage of the head is not changed within a specific time.           
E157    The voltage of the head is out of the specifications. 
E160    The temperature of the head does not reach a specific temperature within a specific time.  Related BJ head temperature control    
E161    The temperature of the head exceeds a specific temperature.           
E170    When the pulse motor for the head scan is driven, it cannot be detected by a sensor within a specific time.            Related BJ head scanner        
E171    The motor is not connected to the pulse motor driver PCB for the head scan.         
E172    The gate array employed to drive the pulse motor for head scan is faulty.   
E180    The motor is not connected to the vertical scanning pulse motor driver PCB.          Related BJ paper feed           
E181    The gate array employed to drive the vertical scanning pulse motor is faulty.          
E182    After the vertical scanning motor is driven, the phase sensor cannot be detected within a specific time.    
E183    After the registration roller cam clutch 2 is turned ON, a given paper size cannot be detected within a specific time.  
E190    RAM directly connected to CPU is faulty.    Related CPU (printer unit)     Failures in RAM of the laser controller are indicated with detail codes.     
E191    An error occurs in the communication with the microcomputer (D/A converter) for high voltage use.            Machines which do not have detail code function may use this code.         
E192    An error occurs in the communication with A/D converter.  
E193    The gate array is faulty.         
E194    The auto registration is faulty.
Data from the # pattern reading CCD is invalid.      
E195    ROM failure -> No. of times data is written on EEPROM reaches the upper limit. 
E196    EEPROM failure: EEPROM read and write error (except software counter), an error in EEPROM areas on DIMM.           
E197    An error occurs in the communication within the printer:
•Errors continuously occur in the communication within the printer.
•Interruption during receiving is not made within a specific time.    
E198    An error occurs in IC on the DC controller.


Canon Error Codes E200 - E499

E code Description      Category         Remarks         
E200    When the scanner moves forward, the scanner reversal sensor is activated.  Related scanner (mainry, exposure ass'y, control panel)    
E201    The scanner is locked up, and excess current flows to the motor control circuit.     
E202    The scanner does not return to the home position for vertical scanning within a specific time.        This code must not be indicated on the control panel. It should be checked with Service Mode.        
E203    Clock pulses are not generated or the PLL lock is released due to a fault in the scanner motor, etc.                       
E204    When the scanner moves forward, the document leading edge signal is not generated.      
E205    The scanning operation does not complete within a specific time.    
E206    The scanner does not return to the home position for horizontal scanning within a specific time.   
E207    After switching the wire tension of the scanner, sensor input is not made within a specific time.   
E208    (On machines which move the lens and the mirrors separately when setting a copy ratio)
Mirror 4 and 5 do not return to the HP sensor within a specific time.          
E209    The scanner does not return to the CFF home position within a specific time.          This code must not be indicated on control panel. It should be checked with Service Mode.         
E210    The lens does not return to the home position within a specific time. (In the direction of light axis)            Related lens   
E211    The thermistor of the scanner lamp is disconnected. 
E212    The lens does not return to the home position within a specific time. (In the direction of drum shaft)       
E213    When performing slide reading, the scanner comes off from the home position for slide reading.  
E214    Rotation of the scanner fan cannot be detected after a specific time passes.           
E215    The thermistor of the scanning lamp (fluorescent lamp) exceeds a specific temperature.     
E216    The scanner lamp (fluorescent lamp? fails to turn ON after a specific time passes.  
E217    The temperature of the scanning lamp (fluorescent lamp) does not reach a specific temperature while the scanning lamp temperature is controlled.       
E218    •The scanner lamp (fluorescent lamp? is turned ON while it is not properly set.
•The filament of the fluorescent lamp is blown out.  
E219    The thermistor for the heater exceeds a specific temperature while the scanner lamp (fluorescent lamp? is turned ON.     
E220    1. The scanning lamp is turned ON during stand-by.
2. The scanning lamp is turned OFF during copy operation.  Related exposure       
E221    The lamp regulator is faulty due to fluctuation of zero-cross signal. 
E222    The scanning lamp pre-heater is faulty.         
E223    1. The red filter does not return to the HP sensor within a specific time.
2. The red filter stays at the HP sensor after a specific time has passed.       Applied to all color filters      
E224    The blank shutter does not return to the HP sensor within a specific time.  
E225    Insufficient light intensity of the scanning lamp: A specific level cannot be attained for the signal during CCD gain correction. 
E226    A malfunction of the scanner cooling fan is detected.          
E230    The horizontal scanning motor driver PCB is not connected to the CPU PCB.        Related scanner drive unit           
E231    The vertical scanning motor driver PCB is not connected to the CPU PCB.           
E240    An error occurs in the communication between the master and the sleeve 0: Detail code is indicated.            Related scanner CPU communication           
E241    An error occurs in the communication between the master and the sleeve 1.            Machines which does not have the detail code function may use this code.      
E242    An error occurs in the communication between the master and the sleeve 2.            Machines which does not have the detail code function may use this code.      
E243    An error occurs in the communication with control panel.     Machines which does not have the detail code function may use this code.   
E244    An error occurs in the communication between PCBs: CPUs exist on two or more PCBs, so the master and the sleeve are not be separable.           Machines which does not have the detail code function may use this code.  
E245    No. of times data is written on the soft counter memory reaches the upper limit.    
E246    Reading from/ writing to the soft counter memory cannot be done properly.           An error occurs when checking DIMM: CP2120 (EEPROM areas on DIMM)       
E247    The software counter memory PCB and the software counter value stored in SRAM are found inconsistent.           
E248    The EEPROM on the reader controller is faulty.
•Inconsistency between the read data and the write data.
•Inconsistency between the ID in the EEPROM and the ID in the ROM.  
E249    An error occures in the image memory on the image processing PCB           CLC5000       
E250    KEY matrix is faulty. Related control panel 
E251    A fault in the inverter cooling fan is detected.          
E260    The thermistor detects excessive temperature rise of the power supply PCB due to a fault in the power supply unit cooling fan, etc.   Related power supply            
E261    Zero-cross signals fail.           
E262    •Power of the printer is not turned ON when the main power of a host machine is turned ON.
•A failure in the power supply fan is detected.         
E270    The signal for slide reading and the document leading edge detection signal are delayed or not be generated.            Related scanner          
E300    When the main power supply is turned ON after downloading, data of a? unrelated model is found in downloaded data.       Related CPU (scanner)          
E301    A failure in the exposure control of the scanning lamp.        
E302    Shading correction failure.     
E305    Multipurpose RAM failure. (A fault in RAM for image processing and such.)
Detail code is indicated.        
E309    Black offset correction failure.          
E310    Editing failure.            Related gate array      
E313    A fault in the gate array for the motor controller.     
E315    A fault is detected when encoding the image data.
1. A chip failure is found when writing/reading/verifying the image data by using the register of the encoding chip.
2. An error occurs when encoding the image data.    FAX failure    
E320    A fault is detected in the measurement signal from the CCD.           Related CCD 
E350    •The bar code data for backup and the attached bar code data do not match.
•A fault in the Serial No. PCB is detected when power is turned ON.         Related GZ    
E351    1. The GZ PCB is not connected to the CPU PCB.
2. Versions of ROM for GZ are not consistent.        
E352    When registering bar code data with Service Mode, a bar code cannot be read. (a parity error, an incorrect bar code, etc.)      
E353    When turning ON the power, inconsistency of the serial number of the RCON (SRAM) and that of the EEPROM is detected.           
E354    •When turning ON the power, inconsistency of the serial No. of the serial number PCB and that of the controller PCB (SRAM)/counter memory is detected.
•When turning ON the power, it is detected that no serial numbers are assigned to the serial number PCB and the controller PCB (SRAM)/ counter memory.         
E355    When turning ON the power, inconsistency among the serial No. PCB, the controller PCB (SRAM), and the counter memory PCB is detected.     
E400    An error occurs in the serial communication with DF, ADF, and RDF.        Related data line of document feeder 
E401    The pick-up roller does not return to the home position within a specific time.        
E402    Clock pulses of the belt motor are below a specific value.    
E403    Clock pulses of the feeder motor are below a specific value.
E404    Clock pulses of the delivery motor are below a specific value.         
E405    Clock pulses of the pick-up motor are below a specific value.          
E406    Movement of the guide driven by the side guide motor does not complete within a specific time. 
E407    Movement of the tray driven by the document tray motor does not complete within a specific time.         
E408    Clock pulses from the feeder motor are below a specific value.       
E409    Clock pulses of the CP register motor are below a specific value.    
E410    •The pick-up roller height sensor does not generate signals within a specific time as the pick-up motor is being driven.
•The pick-up roller HP does not send out signals within a specific time as the pick-up motor is being driven.            Related feed of deocument feeder     ADF for GP605         
E411    The output of the paper sensor is faulty.       
E412    The lock signal is generated at the time when the cooling fan drive signal is generated.      DADF-D1      
E420    Backup data cannot be read, or the data is faulty.     Related CPU communication of document feeder            ADF for GP605         
E421    Faults occur when writing backup data, or the written data is faulty.           DADF-D1      
E422    A transmission error occurs due to faults in IPC of DF/ADF/RDF. (This error code is detected by DF and it is not notified to a copier, so the error code is not indicated.)          
E431    1. The output of the paper sensor is faulty.
2. The sub pick-up roller does not return to the home position.
3. Clock pulses of the sub feeder motor are below a specific value.  Related sub feeder     
E441    CFF motor failure       Related CFF  
E442    CFF exhaust fan failure         
E443    The CFF lamp regulator failure, the CFF lamp failure, a fault in the CFF temperature fuse, or a fault in the CFF controller PCB.  
E446    The output of the sensor does not change after the CFF mirror drive signal is generated.   
E447    The CFF leaves the home position, and the power to the Sorter is cut off.

Canon Error Codes E500 - E5F9
E code Description      Category         Remarks         
E500    An error occurs in the serial communication with the Sorter or the Finisher, etc.      Related data line of sorter/finisher 
E501    An error occurs in the communication within the Finisher controller.           
E502    Coming off of a sensor connector in an optional device is detected:
•The door sensor, paper sort sensor, non-sort sensor, bin outside paper sensor, staple position sensor, etc. 
E503    An error occurs in the communication between the Finisher controller PCB and the Side Stitcher controller.           
E504    An error occurs in the communication error between the controller PCB and the (height) sensor.  
E505    An error is found in Check SUM for backup RAM when turning the power ON.   
E506    Download fails.         
E507    An error occurs in the communication between the trimmer and the finisher.          
E510    Clock pulses are not generated from the feeder motor.          Related feed1 of sorter /finisher        
E511    Clock pulses from the feeder motor are below a specific value.       
E512    Clock pulses cannot be detected due to a delivery motor failure, etc.          
E513    Clock pulses cannot be detected due to a tandem feeder motor failure, etc.
E514    Clock pulses cannot be detected due to a push motor failure, etc.   
E515    Clock pulses cannot be detected due to a tray feeder motor failure, etc.     
E516    Clock pulses from the low speed feed motor are not obtained.        
E517    The home position of the curl removing pressure roller in the buffer path cannot be detected.       
E518    The feeder motor in the paper holder does not reach a specific speed.         
E520    The stacker unit does not reach the upper limit sensor within a specific time due to a motor failure, etc.            Related stacker1        
E521    Input to the tray position sensor is not made within a specific time due to an offset motor failure of the shift (offset) tray.   
E522    The push bar does not return to the home position within a specific time.   
E523    The reference wall does not return to the home position within a specific time.      
E524    The multi guide does not return to the home position within a specific time.           
E525    Automatic adjustment of the bin paper sensor fails, or an error occurs in the automatic adjustment value. 
E526    Automatic adjustment of the bin paper sensor fails, or an error occurs in the automatic adjustment value. 
E527    Automatic adjustment of the stack tray paper sensor 1 fails.
E528    Automatic adjustment of the stack tray paper sensor 2 fails.
E529    Automatic adjustment of the tray stacking amount sensor fails.       
E530    The guide plate of the stapler unit does not return to the home position within a specific time.       Related stapler 
E531    The stapler does not return to the home position within a specific time.      
E532    The stapler does not return to the home position for the front/rear shift operation within a specific time.  
E533    Automatic adjustment of the paper sensor for the stapler fails, or an error occurs in the automatic adjustment value.  
E534    Bins do not reach the stipulated positions within a specific time while the bin rear end open/close motor is working.         
E535    Clock pulses and such cannot be detected due to faults in the swing unit motor, etc.         
E536    Auto adjustment of the leading edge sensor fails.    
E537    The sheet alignment part does not return to the home position within a specific time while the lower bin guide motor is working.         
E540    The home position of the lead cam cannot be detected within a specific time.         Related bin shift        
E541    Clock pulses from the shift motor are below a specific value.          
E542    The lead cam of the lower bin unit cannot detect the home position within a specific time.
E543    Clock pulses of the shift motor for the lower bin unit is out of the specifications.   
E545    Malfunction of bin flapper 1:
•The sensor cannot detect the operation of the flapper when the flapper solenoid drive signal is generated.
•The sensor detects the operation of the flapper when the flapper solenoid drive signal stops.        Sorter-H1 for CP660      
E546    Malfunction of bin flapper 2:
•The sensor cannot detect the operation of the flapper when the flapper solenoid drive signal is generated.
•The sensor detects the operation of the flapper when the flapper solenoid drive signal stops.        Sorter-H1 for CP660      
E550    An error in the output from the load system of the power supply unit is detected.   Related power supply of sorter/finisher 
E551    A failure in or the stoppage of fans of Sorter/Finisher is detected:
•Power supply fan, punch fan, etc.    
E560    Clock pulses from the upper feeder motor are below a specific value.          Related feed2 of sorter/finisher           
E561    Clock pulses from the lower feed motor are below a specific value.
E562    Automatic adjustment of the folding unit feed path sensor 2 fails.  
E563    Automatic adjustment of the folding unit feed path sensor 3 fails.  
E564    Automatic adjustment of the upper path external bin sensor fails.   
E565    Automatic adjustment of the lower path external path sensor fails. 
E570    The side gripper motor does not reach the stipulated position within a specific time as it is in operation.            Related stack handling unit   
E571    The front gripper motor does not reach the stipulated position within a specific time as it is in operation. 
E572    The side gripper left/right shift motor does not reach the stipulated position within a specific time as it is in operation.       
E573    The front gripper left/right shift motor does not reach the stipulated position within a specific time as it is in operation.       
E574    The front gripper front/rear shift motor does not reach the stipulated position within a specific time as it is in operation.       
E575    The cable wiring unit up/down motor does not reach the stipulated position within a specific time as it is in operation.       
E576    Automatic adjustment of the edge feeding sensor fails.       
E577    The paddle drive motor cannot detect the paddle home position within a specific time as it is in operation.           
E578    •The knurl belt motor does not detect the home position within a specific time as it is in operation.
•The knurl belt motor does not leave the home position within a specific time as it is in operation.
E580    The stack tray motor does not reach the stipulated position within a specific time as it is in operation.            Related stacker2        
E581    The stack unit shift motor does not reach the stipulated position within a specific time as it is in operation.           
E582    The tray leading edge stopper motor does not reach the stipulated position within a specific time as it is in operation.       
E583    The sensor is not turned ON within a specific time as the tray auxiliary plate motor is in operation.           
E584    •The shutter sensor is not turned ON within a specific time as the shutter drive motor is in operation.
•It is detected that the shutter detection switch is turned OFF as the tray up-down motor is in operation.
E585    The shutter HP sensor is not turned ON within a specific time as the paddle motor is in operation.           
E590    •The punch motor does not detect the home position within a specific time as the punch motor is in operation.
•The punch motor does not leave the home position within a specific time as the punch motor is in operation.            Related punch unit     
E591    Automatic adjustment of the punch scrap sensor fails.         
E592    Automatic adjustment of the punch trailing edge sensor fails.         
E593    •The puncher cannot detect the home position as the side registration motor is in operation.
•The puncher does not return to the home position as the side registration motor is in operation.   
E594    •The punch paper end HP sensor does not detect the home position within a specific time as the punch sensor shift motor is in operation.
•The punch paper end sensor does not return to the home position within a specific time as the punch sensor shift motor is in operation.     
E595    Output of the punch waste delivery sensor does not change within a specific time as the punch waste delivery motor is in operation.            Side Finisher-D1        
E5A0   Errors in the trimmer knife motor:
a. The knife motor does not leave the home position within a specific time after the normal rotation drive starts.
b. The knife motor does not return to the home position within a specific time after the normal rotation drive starts.
c. In case of b, the knife motor does not return to the home position after the reverse rotation drive starts.
d. Rotation of the fan motor accompanied by the knife motor is unstable.   Related trimmer         
E5A1   Errors in the trimmer holder motor:
a. When the trimmer holder motor goes down, it does not reach the lower limit home position within a specific time after the holder motor starts to be driven.
b. When the trimmer holder motor goes up, it does not reach the upper limit home position within a specific time after the holder motor starts to be driven.         
E5A2   Errors in the trimmer pusher motor:
a. When a stack is pushed out, a stack does not reach to the stipulated push-out position within a specific time after the pusher motor starts to be driven.
b. When a stack is moved to the stand-by position, a stack does not reach the stipulated stand-by position within a specific time after the pusher motor starts to be driven.      
E5A3   Errors in the trimmer trailing edge stopper motor:
a. The trailing edge stopper motor does not reach the home position within a specific time after the motor starts to be driven.
b. The trailing edge stopper motor does not reach the stipulated position within a specific time after the motor starts to be driven.       
E5A4   Errors in the trimmer press motor:
a. The press motor does not reach the home position within a specific time after the motor starts to be driven.
b. The press motor does not reach the press position within a specific time after the motor starts to be driven.           
E5A5   An error in the trimmer feed motor:
a. A fixed speed is not obtained within a specific time after the feed motor starts to be driven.     
E5A6   Errors in the trimmer stopper trailing edge motor:
a. The motor does not reach the stopper functioning position within a specific time after the stopper release motor starts to be driven.
b. The motor does not reach the stopper releasing position within a specific time after the stopper release motor starts to be driven.       
E5A7   An error occurs in the communication between an trimmer and the CPU of the finisher.    
E5F0   •The paper positioning plate HP sensor is not turned ON within a specific time while the positioning plate motor is being driven.
•The paper positioning plate HP sensor is not turned OFF within a specific time while the positioning plate is being driven.   Related saddle stitcher          
E5F1   The detection pulse of the motor clock sensor for folding is below a specific value.           
E5F2   •The guide HP sensor is not turned ON within a specific time while the guide motor is being driven.
•The guide HP sensor is not turned OFF within a specific time as the guide motor is being driven.           
E5F3   •The alignment plate HP sensor is not turned ON within a specific time while the alignment motor is being driven.
•The alignment plate HP sensor is not turned OFF within a specific time as the alignment motor is being driven.
E5F4   •The stitch operation HP sensor is not turned ON while the stitch motor (rear) is being driven.
•The stitch operation HP sensor is not turned OFF while the stitch motor (rear) is being driven.    
E5F5   ·The stitch operation HP sensor is not turned ON within a specific time while the stitch motor (front) is being driven.
·The stitch operation HP sensor is not turned OFF within a specific time while the stitch motor (front) is being driven.  
E5F6   •The paper push plate HP sensor or the paper push plate leading edge position sensor is not turned ON while the paper push plate motor is being driven.
•The paper push plate HP sensor or the paper push plate leading edge position sensor is not turned OFF while the paper push plate motor is being driven.
•The number of detection pulses of the paper push plate motor clock sensor is below a specific value.      
E5F8   Coming off of a sensor connector in the side stitcher is detected:
•Guide HP sensor, paper push plate HP sensor, paper push plate leading edge position sensor, etc.           
E5F9   It is detected that a door switch (power supply system) of Saddle Finisher is 'OPEN' while a copier is working.
•Inlet cover, front cover, delivery cover.

Canon Error Codes E600 - E699
 
E code Description      Category         Remarks         
E600    A failure in RMU extension of an external unit.        Related memory unit (digital APC)   
E601    •An error occurs in the communication with an electric sorter.
•An error occurs in the communication with an image server.
•An error occurs in the communication with a hard disk.     
E602    Hard disk failure.       
E603    Blowout of the fuse on the bus line of the SCSI board.       
E604    Failures in the image memory (including encoding memory):
•When writing/reading/verifying an image memory, a writing failure is detected.
•RAM failure, a failure in mounting the expanded memory.
E605    A fault in the battery for image memory.
Although the battery is charged sufficiently and the power is ON within its discharging time, the battery is below a specific voltage.        
E606               
E607    Input to the clock signal is not made after a specific time passes while the hard disk fan is being driven.  
E608    A fault occurs in the operation controller CPU.        
E620    1. An error occurs in the serial communication with the NP editor, etc.
2. All errors occurring in the editor controller PCB are indicated on a host machine.Related  Editer          
E621    An error occurs in the communication between an editor and a copier.        
E624    An error occurs in the serial communication between the editor controller PCB and the digitizer PCB.     
E625    An error in RAM on the editor controller PCB.        
E626    An error in the LCD controller circuit on the editor controller PCB 
E627    An error in the gate array on the editor controller PCB.       
E628    An error in the IC for communication on the editor controller PCB.
E629    An error in the main sequence on the editor controller PCB.
E630    The projector is not connected. (Blowout of the projector lamp, insufficient light intensity, and a communication failure are included.) Related projector       
E631    A failure in adjustment of light intensity of the projector lamp. (This is detected by a host copier).           
E632    The home position signal for the projector is not input.        
E633    An error occurs in the serial communication with the projector, etc.
E634    Disconnection of the projector lamp is detected.      
E640    •An error occurs in the communication with the IPU.
•An internal error occurs in the IPU.
•The type of an external device cannot be identified.
•An error occurs in the communication with the AHS (PCB for BJ-A1).     Related IPU   
E641    DOS program execution error (upon startup).           
E642    An error occurs in the communication between the image processor PCB and the system unit PCB (upon startup).          
E643    Image memory PCB failure (upon startup).   
E644    Faults related to the interface PCB accommodated to a model (upon startup).       
E645    Faults related to the SCSI interface PCB (upon startup).     
E646    Faults related to the LAN card (upon startup).         
E650    An error occurs in the communication with the film scanner.            Related film scanner  
E651    The CCD is not exposed to light even if the mirror solenoid is ON.
E652    The lens cannot detect the home position due to AF motor failure, etc.       
E653    Signals are not generated from the filter sensor within a specific time.        
E654    Scanner motor failure.
E655    Auto carrier failure.    
E656    Although the carriage drive motor is being driven, the sensor does not send out signals within a specific time.           
E657    EEPROM backup data is damaged.  
E660    A malfunction of IC card. (This is detected by a copier.)      Related IC card         
E670    An error occurs in the communication between the multi device controller PCB and a copier. Related multi device controller        
E671    Abnormal temperature rise in the multi device controller unit.         
E672    A failure in the HD (hard disk) in the multi device controller unit.  
E673    A failure in the HD (hard disk) for FAX use in the multi device controller unit.     
E674    FAX PCB failure.       Including FAX PCBs other than the multi device controller unit     
E675    An error occurs in the initial communication between the IP and the PRCON:
When a system power supply failure occurs, the PRCON is shut down. In this case, interrupt signals keep being sent to the IP, and consequently the IP gets locked up. -> If an error is found in interrupt signals during the initial communication, the error code is indicated.          
E676    An error occurs in the initial communication between the PRCON and the PS:
When the power supply is instantly shut off, the IP and the PRCON are reset and start rebooting. Meanwhile, the PS is not reset, and is left behind, resulting in no PS board. -> An initial communication failure is detected upon starting up the PRCON, and the error code is indicated if a failure is detected.   
E677    An error occurs in the initial communication between an optional controller and an accessory.      
E678    A communication cutout error between an optional roller and an accessory.           
E679    A communication protocol error between an optional controller and an accessory.

Canon Error Codes E700 - E999
E code Description      Category         Remarks         
E700    An error occurs in the serial communication.  Related data line         Related to the data line between the scanner ass'y and the printer ass'y.     
E701    Status parity failure.    Related to the data line between the scanner ass'y and the printer ass'y.      
E702    Command illegal failure.Related to the data line between the scanner ass'y and the printer ass'y.  
E703    Command parity failure.Related to the data line between the scanner ass'y and the printer ass'y.  
E704    Status busy failure.Related to the data line between the scanner ass'y and the printer ass'y.           
E705    Print request failure.Related to the data line between the scanner ass'y and the printer ass'y          
E706    Print request failure:
•After finishing a copy operation, a copier does not go into the stand-by state.
•After turning the power ON, a copier does not go into the stand-by state. Related to the data line between the scanner ass'y and the printer ass'y.           
E707    Related to the data line between the scanner ass'y and the printer ass'y.     
E708    Related to the data line between the scanner ass'y and the printer ass'y.     
E709    Related to the data line between the scanner ass'y and the printer ass'y.     
E710    An error occurs in the communication IC of a copier upon turning ON the power.  Related data line         A copier detects an error in the communication between a copier and an external device. An external device does not have a display function.      
E711    An error occurs in the communication IC of a copier after turning ON the power.   A copier detects an error in the communication between a copier and an external device. An external device does not have a display function.         
E712    An error occurs in the communication IC of the feeder/editor.         A copier detects an error in the communication between a copier and an external device. An external device does not have a display function.         
E713    An error occurs in the communication IC of the sorter.         A copier detects an error in the communication between a copier and an external device. An external device does not have a display function.     
E714    An error occurs in the communication IC of the IC card.      A copier detects an error in the communication between a copier and an external device. An external device does not have a display function.     
E715    An error occurs in the communication IC of the CFF.           A copier detects an error in the communication between a copier and an external device. An external device does not have a display function.     
E716    An error occurs in the communication IC of the Pedestal.     A copier detects an error in the communication between a copier and an external device. An external device does not have a display function.     
E717    •An error occurs in the communication IC of ASSIST.
•An error occurs in the communication between a copier and ASSIST.
•ASSIST is dismounted without releasing it using Service Mode (COPIER>OPTION>INT-FACE>B-CLR) after ASSIST is mounted.      A copier detects an error in the communication between a copier and an external device. An external device does not have a display function.         
E718    An error occurs in the communication IC of the film projector. A copier detects an error in the communication between a copier and an external device. An external device does not have a display function.         
E719    An error occurs in the communication between a coin-operated machine and a host copier.            A copier detects an error in the communication between a copier and an external device. An external device does not have a display function.         
E731    The controller board cannot identify the PDI board. Related internal controller      iR3250           
E732    An error occurs in the communication between the controller board and the scanner.          iR3250           
E733    An error occurs in the communication between the controller board and the printer.          
E734    The controller board cannot identify the image processor PCB.       
E735    The controller board cannot access the PCI bus of the image processor PCB.         
E736    An error occurs in the communication between the controller board and the CCU board (FAX).  
E737    When the controller board accesses the SRAM board, read and write operations fail.        
E738    While the controller board is ON, an error is detected when initializing the network interface board.        
E739    An error occurs in the communication (command) between the controller board and the network interface board. 
E740    An error is detected on the LAN card. Related internal controller   
E741    The controller board cannot access the PCI bus of the network interface board, or the PCI bus is found faulty. 
E742    A fault in the RIP1 board is detected as the result of the self-diagnosis.     
E743    An error occurs in the communication between the main controller PCB and the reader controller PCB (detected by the reader)         
E744    The type of the boot ROM and that of the firmware are different.  
E745    An error occures in the token ring board.      
E750    A ROM designed or a different model is inserted.iR2100   
E800    The auto power off signal of the power supply switch is cut off.      Related power supply and fan           
E801    The auto power off signal of the power supply switch is generated. (No indication. This signal is for ASSIST use.)    
E802    Power saving circuit failure (relay failure).    
E803    •The DC low pressure output (5V, 24V, etc.) of the DC power supply (including the composite power supply) is out of the control value.
•The DC low pressure output (5V, 24V, etc.) is not detected.         
E804    The stoppage of the cooling fan for the power supply unit is detected.        If the cooling fan stops, the temperature of the power supply unit might go up, resulting in flaming or smoking.           
E805    The stoppage of the exhaust fan is detected, or a failure in rotation of the fan is detected. (GP40 or later machines)        The detail code, which can be checked with DISPLAY, was assigned at the end of 1997.
E806    The stoppage of the exhaust fan motor around the ITD (Intermediate Transfer Drum) is detected.           
E807    The stoppage of the exhaust fan motor around the scanner is detected.       
E808    A fault in the fixing drive circuit or the power supply unit is detected.       
E809    The stoppage of the cooling fan of the reader unit power supply is detected.          
E810    The drum cartridge is found not mounted.     Related durable          
E811    Photosensitive drum unit memory failure.     
E812    The home position of the ITD (Intermediate Transfer Drum) unit cannot be detected.       
E813    The fixing unit is found not mounted.           
E814    A specific number of copies are made after warning to replace the drum cartridge is indicated.     
E820    A fault in the drum intake fan is detected.     Related drum/drive-2 
E821    Abnormal temperature rise in the drum cleaner is detected. 
E822    An error is detected in a fan associated with fixing/deliverry.          
E823    A fault in the pre-transfer corona assembly fan is detected. 
E824    A fault in the primary corona assembly fan is detected.       
E825    A fault in the CPU cooling fan is detected.  
E826    A fault in the multi feeder tray fan is detected.        
E827    A fault in the printer's controller power supply cooling fan is detected.       
E830    A fault in the separation fan is detected.        Related charging        
E901    The PLL lock signal is not generated within a specific time after the pedestal motor drive signal is generated.            Related pedestal        
E902    A malfunction of the jogging guide plate of the duplexing unit.      
E903    The paper deck lifter does not lift up within a specific time.
E904    The waste toner box swing cam does not return to the home position within a specific time.         
E999    This error code is used only in case codes for self-diagnosis are not determined while a device is under development. It is not used after the mass production of the device is started.
Reaksi:

0 komentar:

Poskan Komentar

untuk informasi cepat Hubungi No. diatas atau tinggalkan pesan